Overview of the Willem Eprom programmer PCB50B LPT for EPROM, EEPROM, Flash with parallel and serial interface and microcontrollers.
EPROM Chip Programming The operation to EPROM chip is similar to general BIOS chip. The main difference is: the programmer jumper needs relevant ground setup. As an example: write a 27C16(programming voltage is 12.5V): 1. Select the chip and configuration Press chip selection button to select the right chip model, the program displays the DIP.
Briefly: I liked it, went through everything he was fed, adapters are not necessary, but the setting is lame. Details below (lots of letters and pictures).
For AVR ISP and JTAG programmer. The latest AVR Studio software from Atmel. Download here: IC-Prog 1.05D: Dec-22-2004: 7251: It supports most of PIC chips. And it works with JDM programmer, Willem programmer and other programmer: Download here: DOS 0.996 for Willem: 2001: 4757: DOS version Willem programmer software. The REAL/Official willem programmer is made by sivava. Thier latest version is 5.0B. The software that Kee Electronics sends on CD is version 98D12C. This is what you use for 5.0E. On the bottom left of the willem you should see 2 jumpers to set your version. If you set it to 3B mode, then you should use software version 97JA. I did research the chip and there doesn't seem to be a major difference between my 'LF' and the 'VF' model that is listed in the drop down menu in the software. The only noticiable difference comparing both datasheets is 'Single 2.7v-3.6v read / write operations' (VF) and 'Single 3.0v-3.6v read / write operations' (LF). Brand New dual powered (USB/AC) Willem EPROM Programmer latest design PCB5.0. The Latest Version Available. Features and Advantages Can program EPROM, EEPROM, FLASH Burner (Vpp 12.5V, 21V, 25V). The included software is Windows Based and every Version up to and including the latest Version for this Programmer is on the CD.
For the needs of the hobby purchased a year and a half ago with the purpose of the 2764 firmware, OPPSU. Selected on the advice of a seasoned radiocubital as cheap, versatile and omnivorous device. Keygen copernic desktop search 4.
The track is still checked, just lightning fast shipping!
Willem Eprom Programmer Pcb50b Software Download
Packing:
I live in the same box that was sent.
Package contents:
* the programmer; * cable for connection to LPT; * power cable to connect to USB; * PLCC extractor (DIPы is also convenient to pull); * three adaptor (only used a PLCC-DIP);
The programmer:
Obverse: Reverse: Legs inserted himself back up from Athnah motherboard Etched directly on the Board link to the manufacturer’s website, there were a new version of the control program (now in an emphasis do not see them) also have a shop. At the moment, this old version of the programmer sold there for $25.
Dimensions: It represents the bare cost of the 50V version (now the current version 50F). * left — LPT connector for PC connection; * right-to — USB “printer” (type In) — powered device, just not visible. Is used to program the chip to 12V (I’m pierced and 14.5-volt) The orange box xbox 360 iso torrent. * also on the right connector for external power supply 9-12V is desired for programming circuits with voltage of up to 25V.
The chip installed in the cots. All the small radio signed on the Board — name and the value. In the event of breakage repair should not be very difficult.
On the Board there are:
1) block dip switch for configuration; 2) in random places scattered jumpers responsible for the programming voltage; 3) ZIF32 socket for programming of chips in PDIP and adapter; 4) are soldered directly on the PCB adapter for:
PLCC32,
FWH/LPC PLCC32 (the so-called Intel habbie stick),
SOP8 serial flash series 24, 25, 93,
16-pin timesit for the PIC
pins for in-circuit programming (ICSP)
Indication — 4 LEDs:
POWER yellow power lights up when connected to LPT and/or USB
VCC green — lights when power is applied
VPP red — lights up when power is applied
Green green — lit in the flashing process
Soft
At the time of purchase the current version was 0.98D12с4 — glitches are not seen. System requirements — XP, run as administrator. An earlier version of D10 is running under Win 9x. (Personally ran it on a laptop P75, 40MB memory вин95.) When running draws this window: In the main window at the top is a menu of the action buttons below. Left: the choice of the model of the chip for firmware and configuration switches and jumpers and mysterious sliders. Below — additional settings (depend on the selected chip). There are automobielen modern flash drives, but it works not always correctly. Right: schematically shows the correct installation of the chip; Below is the port configuration and programmer.
Top menu: File — load/save image to flash: Edit — only active in browse mode buffer; Device — select the model of the chip for the firmware; Action — actually lists the actions themselves with a chip buttons line below; Help — test connection with the resetter, the link to the home page.
Screenshots
What the chip knows the program (briefly)
The Willem EPROM Programmer can support CHIPS(EPROM,EEPROM,FLASH,I2C,PIC,MCS-51,AVR, 93Cxx, ISP)
Configs tuning programmer is not used. Perhaps we can put hands the firmware settings of dataset on an unknown stick)
Test H/W — oddly enough — a test of iron programmer! When installing uncheck the checkbox the signal of high level to the corresponding ZIF connector.
I personally came in handy. The first time after purchase and wrote mostly 2764. Then came the need to record megabite stick and was a bummer! Enrolled only half. Dancing with a tambourine, change software version, pendrive system вин95 and вин98 nothing. It turned out that one of the address lines is not receiving signal. By comparison detalnogo Board with photos from the Internet was that the cunning Chinese nedolozhili 1 jumper! After installing it everything worked as expected. Everything seems to cost, but osadochek remained…
CFG PIC 18Fxx is unknown to me why this page.
And at the bottom status bar with messages about the successful operations or errors.
Found here’s the motherboard: it is a USB flash drive Winbond W25X40 Decided program right! The reading process takes 38 seconds, the entry — 44 verification — 38 S. Total: entry+verification — 1 min 22 sec.
Also tried with normal and abovie PLCC32 EEPROM in DIP housings — all were considered and prosilog a Bang!
The extractor is quite easy — do not bend, tenaciously holds the chips, it is possible to pull out them not only PLCC, and DIP, but
Adapter tried only PLCC->DIP works The other two are not useful yet.
TOTAL: + flashed everything tried to feed him; + – Board soldered directly into a variety of beds for chips in different packages; + package working out of the box — no purchase is required; + extractor included
Enhanced Willem Eprom Programmer
— works through LPT, which is rarely found on modern computers. — no housing; — configured a bunch of jumpers and switches. (say in case of wrong configuration, you can burn, but I never did); the Chinese do not put 1 jumper, but I was happily corrected; — complete disk with software — it’s just a bunch of garbage.
However, I was happy with it 100%, you can take.
Willem Eprom Programmer Pcb50b Software Download
P. S. So as not to dissolve in the comments the debate about the appropriateness of this programmer and the availability of port LPT, to clarify: I need it just for the firmware flash drives is basically a small amount of parallel access. The presence of LPT is not annoying, because I have a lot of iron supporting it.